Відео

Bench grinder has worked fine for me and everyone other pipe welder I know. Just can’t be an idiot.

For a second I thought this guy was demonstrating a product for sharpening nails

Looks like you just don't know what ur doing buddy😂

Flux isn’t suppose to be used for thin or sheet metal 🤦🏽‍♂️

Gorilla tape and superglue

Can it be used on top of metal etched with phosphoric acid?

Can I apply on top of a painted van bed?

Step 1... Ball the tip. Step 2... Claim the arc is tighter because the thing you're selling Step 3... Profit

I got one of these for patch panels. Works great. I install slip on rockers, wheel well arches, ect. Its all i need. Lot easier than the flux core I was using before

C'est inspirant de voir à quel point cette conversation rassemble des gens de tous horizons. C'est un véritable creuset d'idées.🍭

Earl Schieb used to advertise the 1 hour paint job. They must have skipped a step or 2.

Is this a canned single stage paint then? Was this a 2 k version where you have to activate the can? Looks good

The first 5 minutes is basically an ad for 5 tools from Eastman!

He said, “You see it…😄” 😭😭😭 cold

Sounds like the music from Happy Gilmore😂. Great video

Ceramic or fine grit sandpaper will do the same or better

can you make fuel line flare for your demonstration video

Guess this would work perfectly on steel bike frames

no clear coat ?

I have a small rust spot about the size of my baby finger. I noticed it on the inside of the door tonight when I opened the back door of my 2009 Tahoe. Do I need to treat the rust before the encapsulated is brushed or sprayed on? And is there a different kind of encapsulated for the inside of the door?

Kevin always looks stress

How can I get a new welding chart?

Maybe learn to weld first ? 😂

Man you did a good job that's a beautiful Camaro

That's cool but a bench grinder works fine if you don't file the end of the rod between clips lol

really, you could have done the second one just as well with a bench grinder

Great insights!

Um... I think I'll go back to the video where they painted their van with a roller and tractor paint. I don't see beginner here at all.

"hello my names chef ramsay today ill be baking engine par- wait what the fuck?"

can you do a proper video of laser welding tool at are it good and what kinda deeps we talk about i bet many would be happy to see proper testing video or cars panel fixing videos and greettings from Finland

NOT a dad,never been married, no children

I have an application I am considering using this on. I have an old hvac unit that has rust on an internal component. The HVAC company has advised me that the unit cannot be replaced due to it's age. It is currently still working and I want to prolong it's life as long as possible so scraping rust off at this point is probably not a good idea. Maybe a mild rub with one of your spray products will do the trick. Can I use one of your products to protect it from further rust. Maybe add a coat of liquid metal and then encapsulate it. This is a heat and air unit. Do I need to get a respirator to apply these products? I have an n95 mask. Not sure about the 350 degrees you mentioned in this video.

What is the product name?

Super impressive man. This was fun to watch. Real skill in action.

Funny how it's only the best welders coment, but ya this is pretty bad

Hahhaha..... that is 100% NOT stich welding....thats tacking

What a great way to practice. With pen, paper and the rod

How to spend a shitload of time and energy that you don't have, plus a lot of money too...

My THC dives down very close to the material after piercing almost crashing, any idea what parameters I could change to solve this

Until you lower your prices, I will be calling you up for free Tech Support and then making my purchases at all the Harbor Freight

Dry sanding at it's finest

How expensive is it to do this to ur whole car?

Every era has had them, just by different names. If you look back at the 40s and 50s you'll see 'em there too. To each his own. I respect anyone who wants to have fun with old iron. Just be safe. My neighbor, with the lettering and pinstripe shop next door built one with a flattie in it and wound up selling it to Billy Gibbons. That Billy Gibbons. He held a neighborhood show every year, good ppl. There's a photo album at my website.

I have used weight stack gym machines that need refinishing. I would rather not disassemble the parts, nor transport the machines. What would be the best option to refinish them on site?

❤❤❤❤❤

If you're afraid of guns then maybe this is your thing?

A solution looking for a problem. You can get a good tip off a bench grinder if you just learn how.

its because you cant weld... LOTS of auto guys are using flux and do an awesome job, seen it myself

hahaha, well that looks like shit. Man, what a way to start the video. Love it

Matt from Iron Trap Garage!